Attention! Input results shown will be +/- 10% from middle value. Hint: The closer your min and max inputs are, the more accurate your results will be!

Attention! Input results shown will be +/- 10% from middle value. Hint: The closer your min and max inputs are, the more accurate your results will be!

Attention! Input results shown will be +/- 10% from middle value. Hint: The closer your min and max inputs are, the more accurate your results will be!

Attention! Input results shown will be +/- 10% from middle value. Hint: The closer your min and max inputs are, the more accurate your results will be!

3/32" (0.09375) Inch Inner Diameter Stock Torsion Springs

Definition of 3/32" Inner Diameter Torsion Springs:

A 3/32" (three thirty-seconds of an inch) inner diameter torsion spring has an inner diameter of 0.09375 inches and may fit over a mandrel or shaft diameter of approximately 5/64" (five sixty-fourths of an inch). You will find them in our standard torsion spring catalog where you may buy ready-made torsion springs.

 

The Spring Store by Acxess Spring provides you with an extensive stock torsion spring catalog which you may search through. Below is a list from our catalog where you may find your 3/32" inner diameter torsion springs.

 

Showing 25 out of 954 items

 

 

Select.TSS Part#Inner Diameter by FractionsInner Diameter (in.) DecimalsOuter Diameter by FractionsOuter Diameter (in.) DecimalsLeg Lengths (in.)Body Length (in.)Rate (in.-lbs./Deg.)Sugg. Max. Defl. (deg.)Sugg. Max. Load (in.-lbs.)Total CoilsWire Dia. (in.)Sugg. Madrel Size in Fract.Sugg. Mandrel Size (in.)Material TypeFinishWind Direct.
PT012-110-6.000-MW-LH-0.380-N-IN 3/32 = 0.086 7/64 = 0.110 0.380 0.090 0.00028 158 0.044 6.000 0.012 5/64 = 0.070 MW-Music Wire N Left Hand
PT012-110-6.000-SST-LH-0.380-N-IN 3/32 = 0.086 7/64 = 0.110 0.380 0.090 0.00026 143 0.037 6.000 0.012 5/64 = 0.070 SST-Stainless Steel N Left Hand
PT012-110-6.000-MW-RH-0.380-N-IN 3/32 = 0.086 7/64 = 0.110 0.380 0.090 0.00028 158 0.044 6.000 0.012 5/64 = 0.070 MW-Music Wire N Right Hand
PT012-110-6.000-SST-RH-0.380-N-IN 3/32 = 0.086 7/64 = 0.110 0.380 0.090 0.00026 143 0.037 6.000 0.012 5/64 = 0.070 SST-Stainless Steel N Right Hand
PT014-124-3.250-SST-RH-0.500-N-IN 3/32 = 0.096 1/8 = 0.124 0.500 0.070 0.00078 73 0.057 3.250 0.014 5/64 = 0.080 SST-Stainless Steel N Right Hand
PT014-124-9.750-SST-LH-0.500-N-IN 3/32 = 0.096 1/8 = 0.124 0.500 0.170 0.00026 228 0.059 9.750 0.014 5/64 = 0.080 SST-Stainless Steel N Left Hand
PT014-124-9.750-MW-RH-0.500-N-IN 3/32 = 0.096 1/8 = 0.124 0.500 0.170 0.00028 250 0.070 9.750 0.014 5/64 = 0.080 MW-Music Wire N Right Hand
PT014-124-3.250-MW-LH-0.500-N-IN 3/32 = 0.096 1/8 = 0.124 0.500 0.070 0.00083 86 0.072 3.250 0.014 5/64 = 0.080 MW-Music Wire N Left Hand
PT014-124-9.750-SST-RH-0.500-N-IN 3/32 = 0.096 1/8 = 0.124 0.500 0.170 0.00026 228 0.059 9.750 0.014 5/64 = 0.080 SST-Stainless Steel N Right Hand
PT014-124-3.250-SST-LH-0.500-N-IN 3/32 = 0.096 1/8 = 0.124 0.500 0.070 0.00078 73 0.057 3.250 0.014 5/64 = 0.080 SST-Stainless Steel N Left Hand
PT014-124-3.250-MW-RH-0.500-N-IN 3/32 = 0.096 1/8 = 0.124 0.500 0.070 0.00083 86 0.072 3.250 0.014 5/64 = 0.080 MW-Music Wire N Right Hand
PT014-124-9.750-MW-LH-0.500-N-IN 3/32 = 0.096 1/8 = 0.124 0.500 0.170 0.00028 250 0.070 9.750 0.014 5/64 = 0.080 MW-Music Wire N Left Hand
PT015-125-9.750-MW-LH-0.500-N-IN 3/32 = 0.095 1/8 = 0.125 0.500 0.180 0.00037 215 0.079 9.750 0.015 5/64 = 0.080 MW-Music Wire N Left Hand
PT015-125-9.750-SST-LH-0.500-N-IN 3/32 = 0.095 1/8= 0.125 0.500 0.180 0.00035 199 0.069 9.750 0.015 5/64 = 0.080 SST-Stainless Steel N Left Hand
PT015-125-9.750-MW-RH-0.500-N-IN 3/32 = 0.095 1/8 = 0.125 0.500 0.180 0.00037 215 0.079 9.750 0.015 5/64 = 0.080 MW-Music Wire N Right Hand
PT015-125-9.750-SST-RH-0.500-N-IN 3/32 = 0.095 1/8 = 0.125 0.500 0.180 0.00035 199 0.069 9.750 0.015 5/64 = 0.080 SST-Stainless Steel N Right Hand
PT015-130-7.000-SST-LH-0.500-N-IN 3/32 = 0.100 1/8 = 0.130 0.500 0.130 0.00045 149 0.068 7.000 0.015 5/64 = 0.080 SST-Stainless Steel N Left Hand
PT015-131-6.000-SST-RH-0.500-N-IN 3/32 = 0.101 1/8 = 0.131 0.500 0.120 0.00052 133 0.069 6.000 0.015 5/64 = 0.080 SST-Stainless Steel N Right Hand
PT015-131-6.000-MW-LH-0.500-N-IN 3/32 = 0.101 1/8 = 0.131 0.500 0.120 0.00056 140 0.078 6.000 0.015 5/64 = 0.080 MW-Music Wire N Left Hand
PT015-131-6.000-SST-LH-0.500-N-IN 3/32 = 0.101 1/8 = 0.131 0.500 0.120 0.00052 133 0.069 6.000 0.015 5/64 = 0.080 SST-Stainless Steel N Left Hand
PT015-131-6.000-MW-RH-0.500-N-IN 3/32 = 0.101 1/8 = 0.131 0.500 0.120 0.00056 140 0.078 6.000 0.015 5/64 = 0.080 MW-Music Wire N Right Hand
PT025-143-41.000-MW-LH-0.390-N-IN 3/32 = 0.093 9/64 = 0.143 0.390 1.160 0.00062 508 0.320 41.000 0.025 5/64 = 0.080 MW-Music Wire N Left Hand
PT025-143-41.125-MW-LH-0.370-N-IN 3/32 = 0.093 9/64 = 0.143 0.370 1.160 0.00062 508 0.320 41.125 0.025 5/64 = 0.080 MW-Music Wire N Left Hand
PT027-147-25.500-MW-LH-0.840-N-IN 3/32 = 0.093 9/64 = 0.147 0.840 0.790 0.00134 239 0.320 25.500 0.027 5/64 = 0.080 MW-Music Wire N Left Hand
PT061-215-21.000-MW-LH-0.930-N-IN 3/32 = 0.093 7/32 = 0.215 0.930 1.480 0.03304 85 2.800 21.000 0.061 5/64 = 0.080 MW-Music Wire N Left Hand

 

 

 

 

 

 

 

Your 3/32" (three thirty-seconds of an inch) torsion spring's measurements and dimensions have a lo to do with your standard torsion spring's force. For this reason, it is very important that the torsion spring's measurements are precise. Changing the wire diameter by even 0.001" (one thousandths of an inch) can make a great difference on how strong your spring will be and how much it will be able to travel; especially with a spring as small as a 3/32” inner diameter torsion spring.

 

The 3/32" (three thirty-seconds of an inch) inner diameter standard torsion springs provided here offer customers a wide variation of rate, load, and degrees of travel capacities. Every spring has its own amount of force due to the different physical dimensions; like wire diameter or total coils. The force chart to the right will explain what adjustments will make your spring stronger (more force) or weaker (less force).

 

For more force, you must either decrease your torsion spring's outer diameter, increase the wire diameter, take some coils out, or reduce the degrees of your torsion spring's free position by only taking a fraction of a coil out so you obtain more force through more travel. For less force, you must increase the outer diameter, decrease the wire diameter, add coils, or increase the degrees of your torsion spring's free position by only adding a fraction of a coil so you obtain less force through less travel.

 

These stock 3/32" (three thirty-seconds of an inch) inner diameter torsion springs are made out of either 302 stainless steel (ASTM A 313) or music wire (ASTM A 228).